When something goes wrong with the wiring in a Matthews home or business, the first question is usually the same: how soon can someone get out here, and what is this going to cost. We handle both on the call. The scope gets worked out before the visit is booked, the price is confirmed before any work begins, and we are available every day from 6:30 AM to 10:30 PM. You do not need to wait until Monday.
Matthews is a city with a housing stock that spans several decades of construction. Homes built in different eras carry different wiring, different panel configurations, and different protection standards. Homes in this area were wired in different decades, and it shows in the panels. Whether the job is a single outlet that stopped working or a panel that has run out of capacity, we figure out what the situation actually requires and get it done to the standard the next inspection expects.
From a single GFCI outlet to a whole-home rewire, the first step is the same: knowing what the job actually involves. The price you hear on the call reflects the scope as it was worked out with you. Three things tend to move a quote in one direction or another. The first is what the fault turns out to be once it is traced, because a symptom at the outlet can point to a loose connection, a failed device, or a wiring problem deeper in the circuit. The second is what has to be opened up to reach it, which varies depending on where the circuit runs and how the home was built. The third is whether the existing panel can carry what is being added.
For repairs, the diagnostic visit identifies the fault and confirms the scope before work begins. For upgrades and new circuits, we run a load calculation against what the panel is currently carrying so the quote covers the full picture. Ask what it covers and you get a straight answer. The price is confirmed before the visit is booked, and any change to the scope is a conversation before work continues, not a line on the invoice afterward.
A vacant unit is the easiest window for electrical work that would otherwise mean coordinating around a tenant's schedule, moving furniture, or interrupting someone's day. Panel upgrades, rewiring sections of a unit, adding GFCI and AFCI protection to circuits that lack it, and correcting code issues from previous work are all jobs that go more smoothly when the space is empty. Property managers in Matthews and the surrounding area regularly use the gap between tenants to handle the electrical work that has been on the list.
Access is straightforward to arrange. We confirm what is needed on the call, work out the scope, and schedule the visit for a time that fits the turnover window. If the job involves the panel or a circuit that feeds multiple units, we talk through what needs to be de-energized and for how long before anything is scheduled. One call is enough to get the visit booked.
We are available every day from 6:30 AM to 10:30 PM, and short-notice calls are part of what we handle. For faults that will not keep, call and we can work out the earliest available time to get the job handled. The scope is worked out on the phone so we know what the job involves before anyone arrives.
For businesses and properties that cannot shut down, we work around the schedule. That means confirming in advance what circuits need to be de-energized, how long they will be off, and what the work involves so the disruption is contained. Tenants and building occupants get the same consideration: we confirm what is needed before the visit so nothing comes as a surprise on the day.
Electrical problems don't wait, and neither do we, so if a breaker is tripping on a circuit that feeds critical equipment or a panel is showing signs of a fault, call (980) 479-9789 and describe what you are seeing.
We will work out what needs to happen and get it on the schedule.
Some electrical faults are straightforward to find. A dead outlet, a breaker that will not reset, a fixture that does not light: these have a clear starting point. Intermittent faults are a different kind of problem. A circuit that trips under load but holds fine at rest, a light that flickers only when it rains, an outlet that works most of the time but fails at unpredictable intervals. These take longer to trace because the fault is not always present when the inspection begins.
Finding an intermittent fault is its own job. It involves working through the circuit systematically, checking connections at every device and junction point, testing under the conditions that produce the symptom where possible, and ruling out each potential cause before moving to the next. Grounding and bonding issues, loose neutrals, and arc-fault conditions in the wiring often present this way. Doing electrical work right matters, and we'll help you get it right, which means not stopping at the first thing that looks like the answer when the symptom points to something deeper.
Finding wiring that was done without a permit, done to the wrong standard, or done by someone who knew enough to connect things but not enough to connect them correctly is not unusual in a city where homes have changed hands and been modified over the years. The first job is figuring out what is actually there: what was done, what code it was supposed to meet, and whether it is a problem that needs correction or work that is out of date but still functional.
Connections made with the wrong materials, circuits that were extended beyond what the wiring can safely carry, grounding that was skipped, and protection devices that were never installed are all things we can correct. The work gets brought up to current code, and we document what was changed. We keep you informed from diagnosis to final test.
Some previous work cannot be corrected in place. Wiring that was run through locations it should not be, connections made without a box, or circuits that were modified in ways that compromise the rest of the system sometimes mean pulling the work and starting the section again. We tell you which category the job falls into before any work begins, and the price reflects the actual scope.
Knob-and-tube wiring was standard in homes built before the mid-twentieth century and is still present in some older Matthews properties. It lacks a ground conductor, which means outlets on those circuits cannot be properly grounded without running new wiring. It also was not designed for the loads a modern household places on a circuit. Replacement involves running new copper branch circuits from the panel to each outlet, switch, and fixture location on the affected circuits. We run a load calculation before the work starts to confirm the panel can carry what the new circuits require.
New outlets, GFCI and AFCI devices, USB outlets, weatherproof exterior receptacles, dimmer switches, and smart switches all fall into this category. Each job starts with confirming the circuit can carry what is being added and that the existing wiring is in good condition at the location. GFCI protection is required at wet locations by current code, and homes that predate that requirement often need it added when outlets are replaced or inspected.
Aluminum branch-circuit wiring was used in residential construction during a specific period and is present in some Matthews homes from that era. The issue is not the wire itself but the connections: aluminum expands and contracts differently from copper, and connections made with the wrong hardware can loosen over time. Remediation involves inspecting every connection point, replacing devices with ones rated for aluminum wiring or installing approved connectors at each location, and confirming the panel connections are correct. We assess what is there and scope the work before anything is scheduled.
The electrical side of a generator installation covers the transfer switch, the connection to the home's panel, and the wiring between them. The transfer switch is what keeps the generator isolated from the utility line during an outage, which is both a code requirement and a practical necessity. We scope the job around which circuits the generator will feed, size the transfer switch accordingly, and confirm the panel can handle the configuration. For the region, where severe thunderstorms and occasional ice events can take power out for extended periods, a properly wired generator connection is the difference between a generator that works and one that is just sitting in the garage.
We serve Matthews and the communities nearby throughout Mecklenburg County. That includes Stallings, Indian Trail, Hemby Bridge, Lake Park, and Mint Hill. The range of work covered is explained on our services page.
If your address is outside Matthews proper, a quick call to (980) 479-9789 will confirm coverage before anything is scheduled.
Yes. We serve Matthews and the surrounding communities in Mecklenburg County, including Stallings, Indian Trail, Hemby Bridge, Lake Park, and Mint Hill.
If you are not sure whether your address falls within the service area, call (980) 479-9789 and we will confirm it before anything is scheduled.
A load calculation works through the total electrical demand the panel is carrying and compares it against the panel's rated capacity. It is part of any job that adds significant load to the system, including panel upgrades, EV charger installation, backup generator hookups, and adding dedicated circuits for large appliances. The calculation tells us whether the existing panel can carry the addition or whether a service upgrade needs to be part of the scope. We run it before the quote is finalized so the price reflects what the job actually requires.
A code correction addresses specific items that do not meet current requirements, such as missing GFCI protection at wet locations, ungrounded outlets, or a panel that needs arc-fault breakers added to bedroom circuits. A full rewire replaces the branch-circuit wiring throughout the home, which is the right approach when the existing wiring is knob-and-tube, extensively damaged, or so outdated that targeted corrections would not address the underlying condition. We assess what is there on the diagnostic visit and explain which category the home falls into before any work is scoped.
Stallings, Indian Trail, Hemby Bridge, Lake Park, and Mint Hill are all covered alongside Matthews.
Call (980) 479-9789 and we will scope the job on the phone, confirm the price, and get it on the schedule. Reach out and we'll get it diagnosed.
We are available every day from 6:30 AM to 10:30 PM.
Call (980) 479-9789 and ask about availability for your address. You schedule it. We power it. Simple as that.
Electrical service reaches these neighboring areas too: Stallings, Mint Hill, Pineville. There is more on our map of towns.
Electrical problems come in every size, from a single dead outlet to a full panel that can no longer carry the load. We handle the complete range of residential and commercial electrical work in Matthews and across Mecklenburg County, and we give you a clear price before anything is scheduled. The table below covers what each service involves, who it fits, and what is practical to know before you call.
| Type of Work | What It Covers | When You Need It | What to Keep in Mind |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular |
| Homes with aging or undersized panels, fuse boxes, or panels that cannot carry added loads like EV chargers or updated appliances | Older homes across Mecklenburg County frequently carry panels sized for much lighter loads than modern households place on them. A load calculation confirms exactly what the upgrade needs to cover. |
| Wiring for Additions & Remodels |
| Homeowners finishing a basement, adding a room, or remodeling a kitchen or bathroom | Remodel wiring is scoped against the existing panel before work starts. We confirm what the panel can carry and what needs to change before the first circuit is run. |
| Older-Home Rewiring |
| Owners of older Matthews homes with wiring that was not designed for modern circuit loads | Homes in this area were wired in different decades, and it shows in the panels. We assess what is there, explain what it means, and walk you through the options before any work is scheduled. |
Call us at (980) 479-9789 to get a quote or schedule a service call. We are open daily from 6:30 AM to 10:30 PM, and we will walk you through exactly what the job involves before anything is booked.
(980) 479-9789